 All the parts Except for modified locking clamp and 6M
Mast |
 Drilling Base Plate 300mm x 300mm x
4mm
|
 50mm Angel x 150mm |
 Base plate with 50mm x 6mm bolts and Nylock Nuts. All bolts
and nuts are stainless steel |
 300mm x 31mm Solid Aluminium center |
 400 mm x 10mm Tent Pegs |
 Pegs are hammed into the ground on a angel. and the 32mm
inside diameter mast slides over 31mm out side diameter solid
center bolted to base. This solid center at the base plate swivels to
make it easy to erect |
 The mast is 38mm x 3mm wall thickness 6m long
cut in half on a 45 deg Angel .and it has a 31mm solid aluminium
center for joining the mast. This makes it very
strong |
 Base Plate and direction locking mechanism  |
 Guy Rope hooks very solid fixture. |
 Extra large guy ropes 6m long. Latching peg should be about
4m from base plate |
 Pick up top end of your mast |
 Walk mast up and hold onto opposite side guy rope when you
get to center.
|
 walk across to latching peg and hook guy rope onto
it At first do this with no Antenna's on your Tower and it is easy
to adjust your guy ropes to the correct length |
 This application is with a
Wooden section on top coated with fibreglass to seal it and a halyard at
the top for attaching wire antenna's |
 This application is with a 1.5m. Top section above
the guy rope hooks for a multi vhf uhf antennas |
 This application is for a Larger
Antenna 2 or 3 Element Tri Band Yagi . The section is only 300mm
above the guy hooks |
 This is the 50 mm Wooden pole coated with resin and
Fibreglass. For two reasons one for sealing it and the other for strength
. The Pulley make the razing of wire antenna's
easy |
 This
is the section that slides over the top of the mast 300mm above guy rope
hooks |
This Tower is very easy to Transport.
As it is only 2 X 3 Meter Sections. It can be put on any car roof rack.
The remainder of the equipment needed packs into a small bag or box . The
Aluminium welding was done by a professional Aluminium fabrication
place |
All the parts Except for modified locking clamp and 6M
Mast 
Drilling Base Plate 300mm x 300mm x
4mm
50mm Angel x 150mm
Base plate with 50mm x 6mm bolts and Nylock Nuts. All bolts
and nuts are stainless steel 
300mm x 31mm Solid Aluminium center 
400 mm x 10mm Tent Pegs 
Pegs are hammed into the ground on a angel. and the 32mm
inside diameter mast slides over 31mm out side diameter solid
center bolted to base. This solid center at the base plate swivels to
make it easy to erect 
The mast is 38mm x 3mm wall thickness 6m long
cut in half on a 45 deg Angel .and it has a 31mm solid aluminium
center for joining the mast. This makes it very
strong 
Base Plate and direction locking mechanism 
Guy Rope hooks very solid fixture. 
Extra large guy ropes 6m long. Latching peg should be about
4m from base plate 
Pick up top end of your mast 
Walk mast up and hold onto opposite side guy rope when you
get to center.
walk across to latching peg and hook guy rope onto
it At first do this with no Antenna's on your Tower and it is easy
to adjust your guy ropes to the correct length 
This application is with a
Wooden section on top coated with fibreglass to seal it and a halyard at
the top for attaching wire antenna's 
This application is with a 1.5m. Top section above
the guy rope hooks for a multi vhf uhf antennas 
This application is for a Larger
Antenna 2 or 3 Element Tri Band Yagi . The section is only 300mm
above the guy hooks 
This is the 50 mm Wooden pole coated with resin and
Fibreglass. For two reasons one for sealing it and the other for strength
. The Pulley make the razing of wire antenna's
easy 
This
is the section that slides over the top of the mast 300mm above guy rope
hooks